Tubular heaters or
Mighty-Blade elements are brazed or welded into a standard pipe flange. Standard
flange sizes include: 3",
4", 5", 6", 8", 10",
12" and 14". Flanged immersion heaters are used in large capacity vessels, in high
pressure applications and are installed by bolting the unit to a matching flange
welded to the vessel wall.
Incoloy Elements, Steel Flange, High Watt Density: Solution water
heating (less than 6% solution of alkaline or acid)
For use in severe industrial
process and solution water where the
high nickel content of the
Incoloy elements will resist corrosion.
Stainless Steel Elements, Steel Flange, High Watt
Density: Process
water heating (less than 3% solution of alkaline or acid)
For use in soap and detergent
solutions, soluble cutting oils,
demineralized or deionized water (specify
passivation and SS flange).
Incoloy Elements, Steel Flange, Medium Watt Density: Corrosive
solution heating (less than 25% concentration), also can
be used to heat air and
other gases where sheath temperature is
limited to 1500 deg. F.
Stainless Steel Elements, Steel Flange, Medium Watt
Density: Corrosive
solution heating (less than 25% concentration), also can
be used to heat air and
other gases where sheath temperature is
limited to 1100 deg. F.
Incoloy Elements,
Stainless Steel Flange, Low Watt Density:
Severe corrosive solution (up to 50%
concentration), lower watt density
and element and flange construction provide
corrosion resistance.
Steel Elements, Steel Flange, Low Watt Density: Medium weight oils such as gear
oils, fuel oils, and other materials where
low watt density is required.
150
Ib. ASA carbon steel flange from 3" to 14" sizes .475"
diameter copper, steel, stainless steel, Incoloy tubular elements, or .275"
x 1" Incoloy
Mighty-Blade elements 90,
45, 30, 22, 15, 13, 8 and 6.5 watts/square inch elements for various processes General
purpose, moisture or explosion resistant terminal enclosures Thermowell
for 3/8" diameter thermostat bulb Tubular
element bends are repressed after forming to extend element life Instruction
Manual with wiring instructions included with each unit
Copper Sheath:
Clean water, freeze protection, hot water storage, boiler and water
heaters, cooling towers, heating of solutions not corrosive to copper
Steel Sheath:
Asphalt, wax, paraffin, tar, fluid heat transfer mediums, petroleum,
degreasing and solvent oils, fuel oils, machine oils, alcohol
Stainless Steel Sheath:
Process water, soap and detergent solutions, soluble cutting oils,
demineralized or deionized water (passivation recommended)
Be certain that the sheath material and watt density selected
are compatible with the material being heated and the operating temperature.
Options: Special
rating or immersion length 316
stainless steel or other sheath material Passivation Electropolishing 300
lb. or greater ASA flange Other
material for flange Built-in
thermostat Thermocouple
attached to sheath for high-limit protection Baffles
to increase material flow velocity Larger
flange sizes Stand-off
terminal enclosure to isolate terminals and wiring from flange
in high temperature process .625"
diameter elements to lower watt density or increase wattage ASME
Certification
Gordo Sales,
Inc. "Heat and Control Specialists"
PO Box 1166,
Layton, UT 84041 (801) 544-4236
Copyright 2002
For any questions (application, technical, availability) please call
us at (801) 544-4236 between 8am and 5pm Monday - Friday mountain time
150
Ib. ASA carbon steel flange from 3" to 14" sizes
Incoloy
Mighty-Blade elements